DuraVent PelletVent – Straight Length Pipe
Features fully unitized, twist-lock construction in 3” and 4” diameters. Listed at 1” clearance to combustibles in the USA and Canada. It can be used in both vertical and horizontal installations. Stainless steel welded seam inner wall, combined with a galvalume welded seam outer wall. Pipe OD is diameter plus 5⁄8”. Galvalume or painted black outer finish. 12” length available with stainless steel outer (SS). To calculate installed length, subtract 1 1⁄2” from each length of pipe.
Overview PelletVent
Patent-pending venting system designed for stoves that burn multi-fuels or oil fuel. Multi-fuels include: wood pellets, corn, cherry pits, switch grass, coffee husks, walnut shells, soybeans, wheat, sunflower hulls, rapeseed, and sugar beets. (Rated for continuous use flue temperatures up to 570° F.) All PelletVent components that come into contact with flue gases are built with an inner wall of corrosion resistant super-ferritic metal.
PelletVent is uncompromised in attention to detail and performance. Select components are available in black to enhance interior aesthetics. Seams are factory-sealed on all elbows, tees, and fittings. Available in 3” and 4” sizes through hardware and home centers.
Details
SKU: 3PVP-06 | 3PVP-06B | 3PVP-12 | 3PVP-12B | 3PVP-12SS | 3PVP-18 | 3PVP-24 | 3PVP-24B | 3PVP-36 | 3PVP-36B | 3PVP-48 | 3PVP-48B | 3PVP-60 | 3PVP-60B
SKU: 4PVP-06 | 4PVP-06B | 4PVP-12 | 4PVP-12B | 4PVP-18 | 4PVP-24 | 4PVP-24B | 4PVP-36 | 4PVP-36B | 4PVP-48 | 4PVP-48B | 4PVP-60 | 4PVP-60B
Materials and Construction
PelletVent for multi-fuel is a double-wall pipe with an inner wall of corrosion resistant stainless steel and a galvalume outer wall. Black painted exterior available.
Clearances
1″ clearance to combustibles in the USA and Canada for appliances using multi-fuels or oil.
Diameters
3″ and 4″
Listings
- c-UL-us Listed to UL 641 (MH8381 and MH14420)
- ULC Listed to ULC S609, ULC/ORD C441 (CMH1439 and CMH1440)
Instructions
- PelletVent® for multi-fuel Installation Instructions
- PelletVent® for multi-fuel Installation Instructions (French)
- PelletVent® for multi-fuel Installation Instructions (Spanish)
Typical Installation
Refer to our Typical Venting Installation drawings to select the appropriate component parts for your installation.
- The inner pipe diameter should match the outlet size of the appliance. For installations that require 4″ vent and the appliance has a 3″ outlet, use an Increaser Adapter 3″-4″.
- Check the appliance manufacturer’s installation instructions to confirm which types of vent configurations are permitted (i.e. horizontal, vertical, chimney reline, etc.). Also, check for any venting restrictions such as maximum horizontal run, minimum and maximum vertical rise, maximum offset, etc.
- Be fire safe! Maintain the minimum clearances (air-space) between the vent pipe and nearby combustibles, as specified in the appliance manufacturer’s installation instructions. Use proper support and bracing. Follow local building codes and have your venting system inspected.
Installation Key
| 1 | Vertical Cap |
| 2 | Storm Collar |
| 3 | Flashing |
| 4 | Cathedral Ceiling Support Box |
| 5 | Pipe |
| 6 | 45° Elbow |
| 7 | Appliance Adapter |
| 8 | 60° Flexible Length |
| 9 | 90° Elbow |
| 10 | Horizontal Cap |
| 11 | Wall Thimble |
| 12 | Celling Support Firestop Spacer |
| 13 | Tee w/Clean-Out Tee Cap |
| 14 | Tee Support Bracket |
Planning Your Installation:
| 1 | Refer to the Typical PelletVent Pro Installations diagram, on the opposite page, to be familiar with some of the standard PelletVent Pro installations and the required component parts. |
| 2 | For a horizontal termination, you will need a Wall Thimble and a Horizontal Cap. The cap must be installed with a 6″ clearance to the outside wall (refer to appliance manufacturer’s installation instructions for other clearances). |
| 3 | For a vertical termination, you will need a Cathedral Ceiling Support Box or Flat Ceiling Support, Attic Insulation Shield (if passing through an attic), Flashing, Storm Collar, and Vertical Cap. |
| 4 | Determine the length of PelletVent Pro pipe required. For a vertical termination, measure the pitch of the roof and select the proper flashing. The required minimum height above the roof is 12″. |
| 5 | Pellet stove inserts in masonry fireplaces will require a flex pipe to snake the vent past the smoke shelf. For transition from PelletVent to an existing DuraPlus Chimney, a Chimney Adapter is available. |
| 6 | For vertical rise of PelletVent Pro on the outside of the house, Wall Straps should be used at 4′ intervals to provide proper support. |
| 7 | Important! Check to be sure that the appliance and the venting system are in compliance with all minimum clearance to combustible requirements. |
The following design recommendations are a general guideline to assist in the design and selection of venting components for your installation. Always follow DuraVent Installation instructions before installing your chimney system (found with the cap or support box).
- Size the vent to meet the appliance manufacturer’s specifications.
- Avoid long runs and excessive use of elbows. Refer to the appliance manufacturer for minimum rise and maximum run configurations for the venting system.
- Use an Appliance Adapter to ensure a proper connection to appliance. Seal adapter to appliance with high temperature sealant.
- Use a Single Tee with Clean-Out Tee Cap to facilitate easy cleaning. It is recommended to use a tee off the back of an appliance.
- In the United States and Canada, maintain the minimum 1″ clearance (air space) from vent pipe to combustibles. Use proper support and bracing. Follow local building codes and have your venting system inspected. Be fire safe!
Product Resources
Catalogs
Bulletins
Brochures
Shipping / Freight / Return Info
Same-Day / 24 hour shipping
Same-Day/24 hour shipping - If we have the product in stock, we can ship
same day if ordered before 12pm Monday - Friday (CST).
Freight Claims Policy
Please follow these very important steps when it comes to Freight Items that are damaged or missing
- Open and inspect the order while the delivery driver is present. If delivery driver does not provide sufficient time to do so, please notate the delivery receipt.
- By signing the delivery receipt without noting any damage or missing items, you confirm that your order arrived complete and in excellent condition.
- Record any damage or missing pieces directly on the delivery receipt.
- Do not discard damaged item(s) or any original packaging. For severe damage, write “Refused due to damage” on the delivery receipt and contact us immediately.
- Report any damage within two business days, including delivery details and photos showing the issue
- Damaged item(s) must be returned within 30 days. Failure to return them will result in a charge to the original payment method.
Return Merchandise Authorization Policy
Please follow these very important steps when Returning Items. Contact our team.
- Submit your return request within 30 days of delivery.
- You will receive an email within 1-2 business days confirming whether your return request has been approved or denied.
- Please also note that a 20% restocking fee may apply to approved returns
- If approved, you will receive an itemized Return Authorization, return shipping labels (if requested), and detailed instructions within 1–2 business days
- From the date this email is received, you will have 14 days to return the product.
- Once AF Distributors receives and inspects the returned item(s), your refund will be issued within 1–2 weeks
- Items returned outside of this process or time frame are not eligible for a refund.
Related products
Shop by Best Sellers
Get In Touch
Call or Text us for our Best Price
It's important to us to go above and beyond for our clients and make sure you make the right decision for your home.